BBE 822A Sonic Maximizer Audio Processor Rack Mounted Unit
BBE 822A Sonic Maximizer Audio Processor Rack Mounted Unit
Condition: In great condition with very minor cosmetic wear. Power cable included., Manual
Photos shown are of the product on hand.
Serviced, repaired if needed, and tested by our techs
3 months electrical, 6 months structural warranty
On used gear, excluding misuse, neglect, unreasonable wear and service items like strings. On top of your rights under consumer law.
Afterpay available on this one
Interest-free layby in store (20% deposit, up to 3 months) · Afterpay up to A$4,000, in store and online · Zip above A$4,000
7-day change-of-mind returns
From the day you receive it. A 20% restocking fee applies, and you pay return postage. Not for strings or mouth-played items. Faulty? No fee, and we pay postage. Returns policy
Pickup available at 16 Chrome Street
Usually ready in 2 hours
Overview
The BBE 822A is an intelligent audio processor designed to solve a series of complex problems as described in the previous section. It is, however, very simple to set up and operate and once installed will function flawlessly without further attention.
It is a dual channel, rack-mountable device for use in +4dBu balanced line level applications, such as those found in recording studios, large concert systems and industrial audio applications. The BBE 822A takes up one EIA standard rack space of 19 inches width and 1.75 inches height (1U). There are two completely separate channels to allow for either full stereo program or two independent mono channels, such as separate processing for a snare drum tape track in channel A and a synthesized bass track in channel В.
BBE applies different phase correction algorithms to three separate frequency bands. A variable front panel control for each channel allows the user to adjust the amount of process desired.
Specs
| Bypass frequency response | DC to 20kHz |
|---|---|
| Process mode frequency response | Program controlled |
| Noise in process mode | -85dBu below 0dBu output level |
| Total harmonic distortion in process mode | Less than 0.1% @ 1kHz @ +4dBu |
| Input impedance | 10k Ohms (balanced or unbalanced) |
| Nominal input range | -10dBu to +8dBu |
| Maximum input level | -23dBu (input clip point) |
| Minimum load impedance for full output | 600 Ohms (balanced or unbalanced) |
| Nominal output level | -10dBu to +8dBu |
| Maximum output level | +23dBu into 600 Ohm Load (clip point) |
| Output impedance | 600 Ohms (balance or unbalanced) |
| Rear panel interface | XLR and 1/4" Tip-Ring-Slevve (Tip is hot) |
| Dimensions | 34cm H x 43cm W x 18cm D. 1u single rack |
| Weight | 2.7kg |
| Serial number | E11548 |
Condition & Warranty
Tested and under warranty. Every preloved item is serviced, repaired if needed, and tested by our techs before it goes on sale. Used gear comes with our warranty: 3 months for electrical faults and 6 months for structural faults. It excludes misuse, neglect, unreasonable wear and service items such as strings and batteries. It's on top of your rights under the Australian Consumer Law.
7-day change-of-mind returns. From the day you receive it, on new and preloved gear. It must come back as you received it. A 20% restocking fee applies, and you pay return postage. Not for strings or anything played with the mouth. If it's faulty, the fee never applies, your Australian Consumer Law rights apply, and we pay return postage. Returns policy
Shipping. Free standard shipping Australia-wide on orders over $199 and under 5kg, with an express option at checkout for most items. Guitars over A$2,000 ship free by courier to Qld, NSW, Vic, ACT and Tas, and half price to SA, WA and NT. Preloved items usually ship the same day or within 72 hours.
